Exactly How to Install a Bath Tub Yourself: Removing and Replacing.
Pest Control ExpertJust how do you feel on the subject of How to Install a Bathtub?

Setting up a bathtub isn't exactly rocket science, but it does require solid plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a moderately challenging job. If the old tub is readily obtainable, the task can move quickly; if you need to open up a wall to remove the old bathtub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require an assistant to leave the old tub and also set in the brand-new one. Ensure you have certified yourself for the job and also are comfortable trying it. As opposed to employing a contractor to take control of a halfway-completed job, it is better to consider using one prior to you begin. Opportunities are you may require a specialist plumber to make tube connections.
This article will help you set up a new tub in your bathroom if you have actually already gotten a new bathtub and do not need to transform the plan of your previous water supply pipelines.
Your tools and product checklist must comprise the following:
Getting ready for the Installment
First of all, the sustaining frame provided with the bath must be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited access that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before moving on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Making use of both wooden boards under its feet, position the bath tub in the needed setting. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also readjusting the feet on the tub until the level checks out level.
To install taps, fit all-time low of the outermost versatile tap adapter to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water system and examine all joints as well as brand-new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the regular outlet for leakages.
Finally, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub must wait until the bath tub has been utilized at least when as this will resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type ought to be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to break a stiff seal, creating the water to pass through the wall between the bath and also the tiling, bring about issues with wetness and possible leaks to the ceiling below.
You can select from a range of coloured sealants to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can crack fairly early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Leave a remark below. We will be interested to know your feelings about this post. We are looking forward to see you back again later on. Make sure you set aside a second to distribute this blog post if you enjoyed it. Thank-you for taking the time to read it.
About